#CHOPPER 2 PROPELLER ON YAMAHA MANUAL#
#CHOPPER 2 PROPELLER ON YAMAHA FULL#

#CHOPPER 2 PROPELLER ON YAMAHA FULL#

See Mercury Accessories Guide for full selection of application specific propellers. *Small labyrinth seal propeller required. View all of our Mercury hub kits for sale at discounted prices here. Honda 75-90 HP outboards 1999 and newer, and 115-130 HP Suzuki 100-115 HP 4-Stroke 2009 and newer, 140 HP 4-Stroke outboards Volvo SX 1996 and newer, OMC Cobra SX sterndrives 1994 and newer, 7.4L 1994 and newer (19 tooth spline)** Cobra and King Cobra sterndrives 1991 and newerĮvinrude/Johnson outboards and OMC sterndrives with V6 and V8 gearcases, Cobra and King Cobra sterndrives 1990 and older** Yamaha 200-250 HP SHO 4-Stroke outboards 2014 and olderĮvinrude and Johnson Outboards, Volvo and OMC Sterndrives:Įvinrude/Johnson outboards and OMC sterndrives with V6 and V8 gearcases. Yamaha 150-300 HP 4-Stroke outboards (excluding V8 models) & 115-250 HP SHO 2015 and newer Yamaha 150-300 HP 2-Strokes, HPDI and VMAX and 130-300 HP sterndrives Yamaha 50-100 HP outboards with splined forward washer Mercruiser XZ & XR Racing Sport and Torque Master Mercury Racing Choppers and Cleavers for V6 outboards Mercury V6 used with surfacing propellers: Revolution 4, Trophy Plus, Fury and Tempest Mercury/Mariner 90-115 HP Fourstroke outboards Mercury/Mariner 90 & 115 HP 1978 and newer Mercruiser 120-375 Alpha and Bravo 1 Sterndrives in non-surface piercing applications Mercury/Mariner 135-300 HP (1' prop shaft) Mercury 150-225 HP 4 Stroke in surface-piercing applications Mercury Racing 400R (any engine with a 1.25' prop shaft)

Mercury Verado 300/350 HP using 5.44' HD gearcase (1.25' prop shaft) Mercury, Mariner, Force Outboards and Mercruiser Sterndrives: A small investment could save you thousands - no matter what prop you're using.įlo-Torq II - Often imitated, never replicated. The Flo-Torq II is designed to sacrifice its drive sleeve well below the failure threshold of most modern outdrives. The Flo-Torq II hub system is the world's first modular hub system for outboards and sterndrives. If you'd like to use one of Mercury's propellers on your Yamaha, Evinrude, Johnson, Volvo, OMC, Suzuki, Honda or Tohatsu or you need a kit for your new Mercury prop, just refer to this propeller hub kit selection chart for the correct Mercury Flo-Torq prop hub kit. Prop installation, inspection and boat operation all need to be done in a safe and responsible manner.Mercury Flo-Torq Propeller Hub Kits Outboard or Sterndrive.When in doubt, dealer assistance is suggested. This is important in determining a suitable propeller pitch. Wide open throttle RPM, with boat on the water in forward gear under normal loading conditions, should fall within the range that is recommended by the engine manufacturer and not exceed the recommended maximum.Engine manufacturer recommends greasing the propeller shaft every 12 months.Make sure all propeller hardware is installed correctly.A new propeller's hub and blades must be checked for sufficient lower unit and trim tab clearances before use.

#CHOPPER 2 PROPELLER ON YAMAHA MANUAL#

It is very important to refer to your engine's Owners Manual for important safety precautions when installing a propeller.

By using this prop finder, you agree that the Solas Science and Engineering Company, Ltd, its dealers and other host entities do not accept any liability and are not responsible for harm to persons or property, damages or costs caused by the installation, handling or use of an indicated propeller or hardware.

** Disclaimer: Pitch estimates and propeller selections made by this prop finder are provided only as a general reference and may not be correct for specific boats under actual boating conditions.

Chopper 2 propeller on yamaha